[00:01:13]   hey friends my name is Aaron Ciotti it's my birthday I'm 43 I fell I got drunk and fell asleep today welcome to whoop Wednesday this will be a little bit shorter of a

[00:01:26]   stream I was supposed to stream 6:00 to 8 it's 6:45 Maggie and I went to poppies our favorite little local Cuban Grill and I had an Margarita that's a Top Gear joke that's

[00:01:43]   a Clarkson joke and I don't really drink anymore because it ruins my stomach and 34 of the way through I was pretty pammer not hammered but I was just drunk

[00:02:01]   and then we came home and I fell asleep that's been my day the the roofer guys came they ripped the good YouTube great great way did way did encoding has been overloaded please

[00:02:18]   please turning down it's consider turning down it says there's nothing I can do YouTube this is what I do every single day for the last 3 years you need to figure it out you

[00:02:31]   losers came home I was like oh I could watch Top Gear for like five M here we are I wanted to get the 103s ready I didn't so I'm going to be doing that now these are the Zing 102s that we

[00:03:09]   tested on Monday nothing wrong with them I just don't need three sets of 102s that perform exactly the same so these Zing 102 2200s are for sale they've had two batteries run through

[00:03:24]   them they're absolutely brand new let me know if you want them I'm going to be taking them off this Frame and then I'm going to put the 103s on the this Frame and then we're going to take the

[00:03:34]   canopy and VTX and aiio out of this Frame put it into that frame before I swap it over to the other frame though I'm going to try to remove the the heat sink with some

[00:03:48]   plastic plastic razor blades we'll see how that goes Stephen Woodruff says if YouTube dies would you stream on Twitch I mean like if if YouTube went under and went away forever I guess I would

[00:04:04]   stream on Twitch but if YouTube is is still around I I will not stream on Twitch FPV people don't hang out on Twitch video Gamers hang out on Twitch so I don't I don't have an

[00:04:13]   audience over there but like if YouTube were to go away completely I would I would either use twitch or I don't know some other streaming service that would pop up to replace the YouTube in the chat

[00:04:30]   Steven Woodruff was first Sky High Charlie hockey rounds Frank Nicholas Arc UK Gusto Timmons raging leite metad skin danzel the terrible Douglas otwell wake and bake lucky coal Powers fing goat

[00:04:43]   Gusto FPV beef FPV a whole bunch of eyes and lowercase L's I guess Striker marshmallow Hunters crom Walter stav daters Kelly t Dan Richmonds hockey rounds Northern Tier

[00:05:05]   Cole Powers cisal Striker CMYK Fork bomb dou a double A what's up brother how are you how you been happy birthday to Brandon's baked beans he was born on the same day in the same year as

[00:05:21]   me that's weird technique Jeff FPV why is it not Jeff PV I'm not mad Jeff py puff BL Riot 9 what's up everybody hopefully I got everyone if not well where's this mic at perfect

[00:05:54]   perfect how's the mic sound any better too loud too loud okay I'm not turning it down if you want to talk to me in the chat all you got to do is type cfpv if you want to support me on the

[00:06:08]   Wild and Woolly Adventure that is doing FPV full-time which I do not recommend had on over to C fv.com and click a bunch of buttons there's a bunch of affiliate links there there's a p

[00:06:20]   link to patreon that helps me out the most you can buy yourself some stuff on Etsy there's a PayPal link if you want to celebrate my birthday with me and you don't want to do a super chat because

[00:06:29]   YouTube will take 30% there's a Fiverr link where you can work one-on-one with me a bunch of other stuff do it Stephen o says happy birthday Sky High Charlie says happy birthday Ark

[00:06:44]   says happy birthday timman says happy birthday dude to those of us who know how to use a rotary phone oh boy or just a phone in general right not a not a not a not a computer

[00:06:57]   with a screen on it tiny little computer with a screen on on it mson says happy birthday to one gangly old weirdo to another Denzel turble says can't stick around just drop by to say happy

[00:07:05]   birthday you magnificent bastard fing goat says happy birthday homie cold Powers smoking fat clouds in your honor beef FPV says happy birthday Striker says happy bday crom says happy bday

[00:07:16]   Walter says Jojo Jojo Jojo judge happy birthday stav says happy birthday ders says happy birthday Dan Richmond says happy birthday Frank Nicholas says video is glitching about every second I I

[00:07:29]   hope you YouTube gets their [@$#%] together I I'm not doing anything different than I ever did and OBS is showing zero dropped Fram so it's on YouTube cisal says happy birthday

[00:07:40]   cuz hope it's all it can be has been so far Striker says se you look good for 43 I didn't think you were my parents age H I'm parents age cmk saysdudes in CiottiFPV see W says if yoube we got

[00:08:00]   that technique says happy bday crom says question for you could you give a quick rundown of what ESC pwm frequency use on what whoop great question crom ESC pwm frequency is way simpler

[00:08:16]   than everybody seems to make it out to be 24 khz is the simple answer 24 khz is going to give you the best breaking performance these motors not only accelerate but

[00:08:35]   they also Break and the breaking force is actually really important when you think about like when you think about like you're flying and the wind hits you and the wind knocks it up like this this back

[00:08:51]   motor is going to make power to fight that well if the wind keeps hitting you that motor is going to keep making power and the thing thing is going to start to fly away even though you might

[00:09:01]   be really low in the throttle or maybe even zero throttle right so the braking what what's also going to happen when the wind hits it like this and pushes it up is that this

[00:09:14]   motor is going to break down and so the more breaking force that you've got the less it's going to want to fly away when the pit Loop is working and so when in out 24

[00:09:31]   khz the only problem with 24 khz is that you lose a little bit of efficiency and a little bit of power over 48 96 can go to hell 96 khz it really you really sacrifice breaking you

[00:09:47]   don't get much extra efficiency or power you do get a little bit but for the most part 96k can can sit on a cactus 40 8 is the way to go if you want a little bit of extra efficiency and a little bit of

[00:10:04]   extra power 24 is what you want if you want slightly better flight characteristics slightly better pit Loop performance and you're willing to sacrifice a little bit of thrust and or

[00:10:17]   efficiency that's it nice and simple best case scenario is to run a BL heli 32 which you can't run on a tiny whoop so micros and 5 in and [@$#%] you can get get esc's that are

[00:10:31]   bl32 there's an option in bl32 for variable pwm and you want to set the low to 24 and the high to 48 and then you get the best of both worlds when you're at zero throttle or low

[00:10:44]   throttle you're going to get the extra breaking performance of 24 when you're at high throttle you're going to get the extra efficiency and power of 48 that's it don't run

[00:10:53]   96 and when whenever you get a quad check the pwm frequency to make sure it's not on 96 there's a couple of aios that come with 96 and they fly like a box full of smashed bum

[00:11:10]   bums at 96 not really but it's a little bit worse so that's it that's it that that that's all you need to know about pwm frequency realistically that's all you need to

[00:11:20]   know about BL heli or blue J there's a million other settings in there and if you go on Facebook the place for bad advice lots of people will tell you all kinds of dumb [@$#%] about how you

[00:11:35]   should set those other settings and how they're incredible and they'll change your world they will not change your world nor are they incredible they do little to nothing and in most cases they

[00:11:46]   work worse the the people that actually know what they're talking about that have tested these the a lot of those different ESC settings have found that the the stock settings are typically the

[00:12:07]   best every once in a while with like a lifter or like a really weird build you might need like change startup power or the timing but 99% of the testing that I've seen shows that

[00:12:25]   the defaults are the best be heli blue J they know what they're doing they know how to set the defaults and why would they not set the defaults to be as good as possible Right like

[00:12:40]   sometimes we don't know better than the developers I know that's hard to believe but sometimes the developers actually know what they're doing so the most recently Chris

[00:12:53]   Rosser did a whole bunch of ESC testing Ryan harell has done a bunch of testing in the past Ryan Harold's website is mini quad testbench Bob rugie Kebab FPV cycle

[00:13:10]    he did a bunch of experimenting with ESC settings a while back and initially he thought there were like big gains to be had and then after a while he kind of realized that it was either Placebo or

[00:13:24]   just whatever an aberration and in the testing and last I talked to him he's back to defaults which is great man like one less thing to screw around with right one less thing to

[00:13:39]   adjust wrong and screw up the flight performance of your rig is is a good thing so there you go there's your there's my five minutes of ESC settings for you good question brother raging Le says

[00:13:58]   happy birthday nor tier says happy birthday my friend BL says happy birthday scrolling back up since YouTube did the thing on my birthday thanks a lot YouTube you jerks Justin Waller says

[00:14:11]   happy birthday rabbit rabbit rabbit rabbit says happy birthday rip some packs for the live stream that's the plan brother we're going to fly six batteries today hopefully a couple of them will be

[00:14:22]   on 103s I'm really excited to see how these 103s are I have a feeling that they're going to be awful heavy I know that they're awful heavy I have a feeling that they're going to be a

[00:14:31]   little bit too heavy I also have a feeling that they're a little bit too big of a motor for a 75mm motoro motor 1.6 in propeller frame if we had better TR and quad blades they might

[00:14:50]   these motors might be okay here but I have had no luck with anything other than the 1.6 in by blades in terms of them being better than the bblades like they're not bad they're

[00:15:03]   just nowhere near as good as the GemFan 1610 bblades but we're here to test damn it and test we shall stav says PayPal for a birthday gift thank you dude maty says do you

[00:15:26]   ever drum and whoop at the same time I do not I'm not good at either one of I'm not good enough at either one of those things to do them at the same time that's not that's not true I'm

[00:15:39]   pretty good at both of those things stav I think this is you Chris K with a $25 PayPal thank you so much brother he says happy birthday here here's the Tylenol and water to nurse

[00:15:54]   The Hangover in your 40s I think I'll escape this hang I don't think I'll hangover this time I I would have it right now if I was going to but poppy gave me water so I'm gonna

[00:16:07]   drink it damn it thank you so much stav very cool of you Frank Nicholas with a $50 PayPal holy hell thank you brother he says happy birthday dude very very very cool very supportive thank you brother

[00:16:22]    Cisco FPV jumping onto the patreon welcome to the gangly gang my friend thank you for the support and just get this out of here Facebook is about to ban me again they continue to say that

[00:16:42]   I've uploaded content that that doesn't meet their copy protection rules I finally figured out what it is it was a link to a live stream one of my live streams in which I

[00:16:55]   did not play any copyrighted material so what I guess is happening is somebody is [@$#%] with me basically this all kind of happened right this all started happen not all of it but some of

[00:17:13]   this recently started happening around the time with the fractal sucks [@$#%] so I'm assuming that someone who doesn't think that fractal sucks is is trying to ruin my career so

[00:17:25]   thanks for that scumbags it might not be that but the timing is awful convenient and I mean there's no other real explanation because there is no copyrighted material in there so it's impossible that if

[00:17:40]   Facebook had some sort of a Content aware copyright filter not only that but it's not content that's on Facebook it's a link to YouTube and I guarantee you that Facebook can't chase the link and then

[00:17:57]   search through the content on Facebook on YouTube even if they could there is no copyrighted content in there so it must be somebody manually manually saying that it's

[00:18:10]   it's copyrighted content so losers will be losers I guess sucks but I I'm completely done with Facebook I I I haven't I'm not going to get on a Facebook rant

[00:18:27]   again life's too short man but shitty people will be shitty people also T-Bone one thank you for joining the patreon man very cool of you much appreciated on the

[00:18:40]   support let's see here I think I'm caught up here I think I'm caught up on emails no I'm not crom jumping onto the patreon as well he's addicted to gambling and he's going

[00:18:56]   to get enter entered into a whole bunch giveaways thank you so much crom for the support enjoy the stuff that you get from joining the patreon man very cool of you much

[00:19:07]   appreciated P Morty with a $5 Super Chat he says happy birthday can't tell you how much I love the streams and just and just chilling talking tiny whoops thank you for all you do for us thank

[00:19:16]   you brother for allowing me to do this for you guys it's very cool of you Frank Nicholas says you've got mail thanks again brother bl550 says damn 30% that's a ripoff h

[00:19:33]   i mean they it's can't look I've got three years of four live streams a week two to four hours each being stored for free on on YouTube that's a pretty good deal All Things Considered you

[00:19:51]   know I can't imagine how many terabytes of data they store for me completely free of charge and then use guys can all access it so it's like taxes you get a you go out and

[00:20:05]   you get a real job and you get like 30% taxes taken from you YouTube does the same thing but then on April 15th you have to pay even more although not much more because you just say that your

[00:20:18]   expenses were pretty much exactly what you made and then you're okay but everybody got to pay taxes I got to pay YouTube taxes it is what it

[00:20:29]   is I'm a lucky guy to be able to do this AJ Farris says happy born day cmk dropping the C fv.com link Fufu Panda says happy bday ppff FPV says happy birthday as well bday as well

[00:20:46]    raging Le says happy bday Northern tear says happy birthday my friend BL says happy birthday where we at here Justin Waller says happy birthday rabbit rabbit rabbit says happy birthday in pack live

[00:21:00]   stream I think we're good there here we go Cisco FPV says if you haven't weigh the 103s before you put them on that's going to be the before you put them on that's going to be the nail on

[00:21:14]   the coffin the 1102s are almost a gram lighter I I know that about the 103s I I I know that they're heavy and a couple people that I trust have said that they're too heavy and

[00:21:26]   I don't doubt it but for example right the meteor 75 Pro frame is something like seven grams heavier it's way heavier but the it doesn't necessarily fly that much

[00:21:45]   worse because you get a bunch more power from the bigger props I have a feeling that the 103s are going to end up on this Frame but I want to try it on the meteor 75 airframe first but

[00:21:58]    let's weigh them matter of fact let's weigh all these motors I didn't weigh the 102s yesterday can somebody pull up a weit ah can somebody pull up a weight for me on the

[00:22:19]    on the BetaFPV 112s I'm certain it's on their website can somebody also find a weight for me on the flywoo 102s because I'm not going to take those off to weigh

[00:22:34]   them I am willing to take one of these RC and power 102s off though I love the idea of weighing the these motors for myself because I have seen websites that are not quite

[00:22:50]   right on their weights before and every scale does can potentially vary a little bit speaking of scales that can vary a little bit if you want to see how much your scale varies join my

[00:23:05]   patreon and message me over on Discord I have a set of calibrated weights that I will rent out to you for the cost of shipping or more if you want to support me a little bit more than that

[00:23:19]    so that you can set your scale perfectly RC in Power 102 is 2.55 grams RC and power 103 is 3.35 gr so8 of a gram heavier I have heard that the BetaFPV 1102s are basically 0.15 of a gram heavier than

[00:23:47]   most of the 102s I flight Zing 102 2.55 grams I'll be damned is it really exactly the same as the RC and power it's pretty impressive 2.55 that's wild because the The

[00:24:08]   Zing has a big old chunk of shrink wrap here shrink wrap is very heavy because it's rubber The Zing has a big old chunk of shrink wrap here and then the wires on The Zing are either thicker or

[00:24:21]   the the insulation might just be thicker than the RC and power the the RC and Power 102 like when you look at it's looks like a really lightweight motor they they skimped they didn't put

[00:24:33]   a piece of shrink wrap here to prot protect the solder joints they used really skinny cables sometimes the really skinny cables are not a different wire gauge they just have thinner

[00:24:47]   insulation but the insulation is like a silicone e rubber e material and it's That's Heavy so I'm actually really surprised that the r and powers are not lighter than The Zing The Zing

[00:25:05]   also has a taller motor Bell on it and it's a two-piece Ah that's why the The Zing weighs the same because it's a two-piece Bell two-piece Bell Motors are almost always lighter because

[00:25:19]   they can use two different materials whereas the RC and power is a one piece Bell so that makes sense interesting though that they both end up at 2.55 grams I that that makes our

[00:25:35]   lives a little bit easier the more 102s weigh exactly the same the less we have to go well I went with this one I forgot forgot I forgot the most important part

[00:25:51]   I went with this one because it's a little bit lighter this mean that egg or like train seals I guess I don't know I don't know what I'm going for

[00:26:05]   there it's gonna get weird tonight Martin tanley says there any input on the best cine whoop 2 to three inch frames for WalkSnail and a GoPro respect your opinion cheers

[00:26:21]    no moving on Moy says Martin that's a good question a 2-in rig to carry a GoPro is going to be a nightmare don't do that 2-in propellers are extremely inefficient and

[00:26:41]   Extremely Loud so a 2-in rig carrying a GoPro is going to suck two and a half start at 2 and a half inch 2 in has pretty much no benefits over 2 and A2 so 2 and a half is is

[00:26:58]   the starting point I don't really like any of the 2 and2 in builds they're all pushers I don't like pushers they force you to run aios and I don't think that pushers

[00:27:13]   have enough propeller protection to fly around people and a main reason to fly a cop is that you're flying around people so for me cine whoops that are going to carry a GoPro start at three inches

[00:27:28]    and my favorite is the FPV cycle sinore it's just it was one of the last C whoops to come out and Bob rugie from fbb cycle used a lot of the lessons that we learned from all the

[00:27:43]   other 3-inch cine whoops and put them into practice and made the lightest and strongest and most well second most configurable customizable cop frame that there is

[00:27:58]   the most configurable is the squirt which is okay but the the squirt is the first cine whoop frame that ever came out they did make a V2 but they didn't really change anything

[00:28:12]   that that matters the worst part about the squirt is how fragile it is mainly because it's a solid base plate and it's just it's just old as hell the the squirt is just a super super super

[00:28:26]   old frame and there's a lot of newer better ones that exist so but the squirt has been around so long and so many people have been using it that there's a ton of aftermarket parts for it and so you

[00:28:44]   can make it so that it's kind of viable basically but it's still old and moldy so one thing that I just noticed is that the meteor 75 airframe has these weird little

[00:29:03]   plastic Pockets that kind of make it easier to mount the motors but not really and then these 103s have these 103s have a motor stator base that allows you to Mount

[00:29:24]   them on the three-bolt whoop stuff or the four bolt toothpick stuff and the Stater base is overlapping these little plastic ears on this Frame but luckily I have just

[00:29:43]   cranked the screws down so hard that it's flattened the it's flattened that plastic out I'm going to go around real quick and crank it even tighter to make sure that these motors are

[00:29:57]   sitting totally flat flat right now I think these motors are sitting a little bit each one which is not the end of the world but it's also not a good thing so the meteor 75

[00:30:12]   airframe ideally what you want to do is cut those plastic ears off those plastic ears are totally worthless they really don't make the motors much easier to mount

[00:30:24]    so on this third one I kind of wish I I should probably cut them off but I did the first three this way I might as well do the last one like this so if you're going to run these

[00:30:39]   103s on a meteor 75 airframe be careful about that either just do what I'm doing and crank the the two inner screws down really hard to flatten the plastic out

[00:30:53]   or cut it ideally cut it because you don't it's not great to be cranking these screws down so hard the the Stater bases on these tiny whoop Motors only give you like a Mill and a

[00:31:08]   half of material to screw into but this plastic is also pretty soft so it's seems to be flattening out pretty easily so there's that which is interesting I wondered why

[00:31:25]   these Mo like when I was trying to line these motors up with the screws I wonder why I wondered why they weren't they were being a little bit more difficult to get lined up properly and now I

[00:31:38]   know let me just check it let me let me confirm that it is overlapping that this one I haven't cranked down yet I could see it's sitting up on that thing but whatever not the end of the world

[00:31:59]   stav we got that Rob oxis says typically me late to the party happily happy gangly birthday thank you brother you didn't miss anything I was late too I got drunk and fell

[00:32:11]   asleep YouTube did the thing again scrolling back up to find my place here we go timman says what is pwm dithering I don't know I'm I would Google it I'm sure Google will tell you some things

[00:32:39]   there was a time where people were saying you need to turn off pwm dithering and I've tried it a couple times and there was no difference so it's not something that's super

[00:32:52]   noticeable I don't know what it is I I never took the time to actually read about it I don't think it's anything that's gamechanging because I haven't when when something makes an actual

[00:33:05]   difference I'll kind of hear about it right like more than a couple of people will be talking about it so and I have turned it off and on and I've noticed no

[00:33:17]   difference whatsoever so no clue Ram dco with a bunch of emojis metad dirin says in the latest blue jay release candidate they're talking about removing 96 because of the

[00:33:29]   lack of benefit I I a lot I wish they didn't ship I I forget what it was but there was an AIO that came I think it was a HappyModel AIO actually that came on 96 and man it

[00:33:46]   flew like ass when I put it on to 48 it was noticeably better Rob axon says for what it's worth check my hd0 m 2024 had a bad motor it was actually a bad motor pin in the plug wow I've seen stuttering

[00:34:04]   with these rigs check the pins very cool wait a second what oh right the HD zero Mobula 6 2024 has the has the the the plug header version of the AO quad 66 says happy birthday thank you

[00:34:22]   brother happy birthday to you as well I haven't done that in a long time somebody brings you your food at a restaurant and says enjoy your food and you say oh you

[00:34:36]   too did anybody hear me everybody [@$#%] heard you free lojo dropping the patreon link thank you dude there's another situation where that happens a lot

[00:34:51]   where somebody that's doing their job says something to you and then you out of just habit or whatever say oh you too and it's and it's the most Soul crushing thing

[00:35:08]   ever there's actually a commercial about that like the kids the the kid's dad did it and then the kid was like horrified Jay hin says happy birthday and a WalkSnail s on the way see your

[00:35:19]   email for tracking info thank you brother I will I'm going to get caught up in my emails tomorrow I finished up my Sunny King Criterium edit today from

[00:35:33]   2023 better late than never I tried to get it done last week but I didn't it turned out really good actually I used the at the beginning of the live stream I played three of the

[00:35:51]    insta360 go-to files at the same time from this year's Sunny King Criterium so look out for that edit in 12 months to two years oh [@$#%] I also have the the 0802 27,000 KV 1 mm motor shaft

[00:36:19]   lightweight blue motors for sale these are the Stater the the 27,000 KV Stater from an igal an OG blue igal motor and then the Bell the the ex the lightweight Bell from the 0802 33,000 KV

[00:36:43]   motor and then the 1 mm motor shaft so for a 65mm tiny whoop these will be pretty good because of the 1 mil shaft you can absolutely run these on a 75mm rig just don't crash the [@$#%] out

[00:36:56]   of it because the 1 mil shaft shaft will not last super long but these are available they do say 33,000 KV on the Bell they are not 33,000 KV they are 27,000 KV and they're pretty

[00:37:09]   fresh the these bells probably have five or six batteries through them just flying in the basement here I don't even think I crashed these upstairs in the hardwood so these

[00:37:20]   bells are pretty fresh and the Staters are very fresh as well so they're basically for all intents and purposes they are ex 0802 27,000 KV Motors that have been mismarked as

[00:37:38]   33,000 KV so they will rip on a 75mm rig on a 65mm rig they're good 27,000 KV is where things start to get interesting if you're not a complete nutcase like I am that's probably enough

[00:37:54]   power for you I do think it's worth it to go 30,000 32,000 with 72s that is my preferred setup but if you're looking to drive like a tribl propeller on a 65 802 is really crank or even a quad blade prop

[00:38:10]    or a 75 that you don't crash all over the place or like if you were going to build a 75 rig and fly it outside and crash into the grass these motors would be awesome you'll be able to run the new

[00:38:27]   uh HQ super lightweight 1.6 inch by blades on these motors and these will Jam these seem to be super they don't seem to be they are a super lightweight 1.6 in propeller

[00:38:42]    they would match up really really really well with those Motors again just don't crash super hard although what's interesting those propellers are so lightweight and so thin that they

[00:38:55]   would not impart a lot of energy into the motor shaft so those HQ propellers would probably be a really good match with these motors versus the the GemFan propellers that are nice and strong that

[00:39:09]   are going to push really hard on the motor Bell so you might actually be able to run those HQ props on these motors and not ruin the motor shaft super quick if you're going to be crashing

[00:39:18]   them Walter says this is not this is not good response they're looking and enjoying your squirming bl550 says I guess I didn't think of that Fufu Panda says what's your opinion on the meteor 65 Pro

[00:39:37]   frame size I have tried the meteor 65 Pro frame a bunch of times over the years and the biggest problem is that there are no by blades for it yes you can cut two of the blades off of the Quad blades

[00:39:53]   but you'll they'll never be perfectly balanced so that's the real problem with that frame the the lightest weight propellers are Tri blades for it and they're pretty heavy propellers and it

[00:40:07]   just doesn't fly good I've tried it with 72s I've tried it with 802s all different KVs lightweight aios regular aios it the the that frame solves a problem that doesn't exist is is the

[00:40:23]   best way that I can put it the 65mm rig are ultra light and they make tons of power now that we have high KV Motors the 75mm frame is really efficient and you can put a big old

[00:40:39]   battery in it 450 or a 550 the 65 Pro frame like you have to run a small battery and it's heavy and there's no good propeller selections so it's it's doesn't do anything all that well like

[00:40:59]   if if you want to go bigger than a 65 go to 75 you're going to have better propeller selection better battery selection if you want to stay nice and lightweight stay on a 65 the the

[00:41:10]    it's it which realistically it's a good thing we what we don't need is is we don't need another frame size in between 65 and 75 are perfect they both do different things really really well

[00:41:28]    what we need are more Motors we don't need more frame sizes we don't need more propeller sizes we need more Motors that's what we need and we need higher KV Motors in a lot of cases so

[00:41:40]   the the meteor 65 Pro I've tried it a bunch of times and it just doesn't there they're the the propellers are so heavy that you have to run that you that you need to

[00:41:54]   run 802s and at that point where you're running a heavy 802 a 75 is way better and so you might as well go up to a 75 at that point the weight and then it

[00:42:08]   just battery life becomes a problem because you got a big heavy motor big heavy props heavier frame it just it's stuck in this weird like no man's land of confusion and

[00:42:22]   sadness that's pretty dramatic but whatever it's fine it's fine it's fine I'm going to put this RC and Power 102 back onto this clearish white

[00:42:39]   frame because I think the RC and power 102s are going to be the ones that I keep the The Zing 102s are definitely for sale I think at some point here the flywoo 102s are also going to be for

[00:42:56]   sale and I I do want to keep one set of 102s because maybe they're good on like a 2-in toothpick I don't know I I'll I'll keep shopping them around to try to find the best possible home for

[00:43:10]   them and these RC and powers are cool looking like the pink and light blue thing is is smexy do the kids still say smexy no oh well they did it one

[00:43:24]   point ramdo says I did a thing see was going to try a vid but I'll show you for a birthday on Discord one second let me know where it is on the Discord fre says happy bday thank you

[00:43:40]   dude Walter says is a full battery more heavy than an empty one better ignore them today it is not electricity does not weigh anything so batteries don't change weight whether they're full or

[00:43:56]   empty AR UK says if you want to put the 103s on the meteor 75 Pro frame I think you have to sand off the little triangles in the frame because of the different Mount does the

[00:44:08]   meteor 75 Pro have those stupid little wings as well I didn't think it did I thought it was just the airframe oh it does it has a whole big it has a whole it doesn't just have like

[00:44:33]   little whatever kill me I did for my birthday though get a set of Dremel attachments a big 180 piece whatever 186 piece Dremel attachment thing so I'll do that

[00:44:55]   not on stream I'll do that off stream for sure SOS Death Valley says happy birthday thank you dude Kevin James says happy birthday M Erin with a $25 Super Chat thank you homie I'll read the comment

[00:45:09]   in one second Walter says I use coins for scaling weights ah it's a good idea limits 20 says happy birthday stav says did you ever find the M4 stick ends looking to try if no

[00:45:23]   one has them nope they are gone the M4 stick it was almost a year ago it was like 10 months ago that there is a shipping label that shows still pending so it either got

[00:45:41]   lost in the mail or whoever the last person that had it's under their desk or whatever maybe somebody will find it someday or maybe the mail will find it and they'll return it to

[00:45:51]   Sender but I have a funny feeling the M4 stick ends are gone it was it was inevitable the the the stick ends went out to a lot of people the M3 stick ends are still

[00:46:02]   around they're still bouncing around between people right now actually so kind of is what it is I I I absolutely knew that that was going to happen and they the the the M4

[00:46:17]   STS stick ends made it to a lot of people before that happened so it was still a good project that we did it was cool scrolling back up because YouTube is a donkey limits 20 says happy

[00:46:32]   birthday St no we got that ramdo says did a couple of picks for you of a 65x idea that might cheer you up ramdo says where's Discord Discord where the hell are you there it

[00:46:50]   is where is it is it in Patron Hangout no it's not well that's interesting Andy welma welma says looking at the most famous denstist Motors a while back and the 16 millimet

[00:47:16]   was on my radar just checked again 3mm titanium shaft Al although bearings are 2x 5x 2 and A2 that's weird so not sure the shaft is 3mm all the way through can't be that's interesting

[00:47:28]   read deeper on roster's page seems like a good option though any input kebabs 16 mm Motors are Ultra notchy so they might cause some like jello issues or they might be really difficult to tune

[00:47:42]    they're also a size that is like a little bit too big for 3 and 1 half in propellers it's more of like a 4in motor and 4in builds are rare because there's not like a camera there's not

[00:47:59]   like an HD camera that really makes sense for a 4-in build so I've I've always wanted to try them but I've I never have because there's just never been a build that that motor would make

[00:48:11]   sense on but someday there will be someday there'll be like an action camera that's like 50 grams and that'll be perfect for a 4-in rig there's a chance

[00:48:27]   that the Avada 2's camera and VTX setup which will be the 04 system I'm guessing there's a chance that that will weigh enough where 4-in rigs make sense so we'll see if if that's so that would be

[00:48:46]   incredible because there are some really good 4-in propellers that are out there so we'll see and it would be nice to see 4-in rigs get some love

[00:48:58]    I'm looking in here's ramono what are you doing ramono what's that you mounted the the G string mount in the front well that's pretty fantastic I a lot

[00:49:19]   actually I never thought to do that that looks like it worked really well too this is the g string Mount that destroys your AO when you when you mount it the way that they want want you to on

[00:49:33]   top of the AO that is really really cool that those the side ears Reach Out far enough to get to the to the motor mounts Jesus if I'd thought to do this I could have saved timens a ton of

[00:49:49]   work although I I I like our little setup better I think man that's good Lord it looks like they've got a bunch of holes here and you use one of these front holes damn

[00:50:05]   dude so the problem with this Mount is going to be that the battery is going to slam into the back of the camera so that's what timman and my's batwing Mount does really really well is it

[00:50:17]   lifts the camera up a little bit from here so that your battery can slide all the way far forward this setup here on a hard crash the battery is going to bash into the back of the camera it's

[00:50:30]   probably not it's probably going to be okay you can probably brace the battery against the back of the camera this looks really strong here so it's probably actually fine but with

[00:50:40]   the Batwing Mount the battery will go all the way forward and then you can run your your BT 2.0 leads nice and short and save a little bit of weight but man this is really cool this is a a

[00:50:50]   really really cool little setup here good [@$#%] dude I like it I like it what else is happening here what's going on in the chat gold power says old lipos how puffy is too puffy for a goggle

[00:51:13]   battery I mean my main concern would be it Lighting on fire against your head so the puffier it is the the better the chances of your hair catching on fire but goggles don't really use they don't

[00:51:33]   pull hard on the battery so the fact that it's puffy it's going to it's only going to underperform like towards the end of the battery life so I guess the real answer to the question

[00:51:42]   would be until it doesn't give you enough life right like because the puffier it gets the more saggy it's going to be so you fully charge it and you run it and if it's

[00:51:54]   brand new you're going to get I don't know an hour out of it as it gets more Puffy you're going to get 40 minutes out of it 30 minutes out of it 20 minutes out of it eventually you're you're going

[00:52:02]   to get so little time out of it that you're like screw this thing but that's about it that and the danger of your head catching on fire are really about it but I

[00:52:13]   mean a puffy battery in a situation that doesn't pull hard on it is a great home for it as long as you're willing to take the the risk although them no no no they they are at more

[00:52:32]   of a risk when they get puffy because they get why do they get puffy they get puffy because the cell the the pouches are starting to leak I think right like there's a tiny little pinhole in the in

[00:52:42]   the pouches or or are the pouches expanding I actually I don't know I don't actually know what the cause of them getting puffy is but I know that when they get puffy they start to perform a lot worse

[00:52:56]    but goggles don't pull lots of amps so won't really matter it's a good question cisc says the 1102s were 2.7 and the 103s are 3.4 I just weighed both so the so 2.5 for 102s

[00:53:18]   2.7 for 1102s 3.4 for 103s I think mine were 3.3 3.35 Maybe so the 103s are heavy but they might make a bunch of power and I'm okay I'm okay with a little bit of extra weight as long as the the biggest

[00:53:39]   problem that I'm trying to fix on these walk nail 75mm rigs is power and sometimes to get more power you have to add weight sometimes you can add a bunch of KV and get the power that you're

[00:53:54]   looking for sometimes that doesn't work sometimes the the motors are already at their maximum amount of heat shed ability and adding a bunch of KV doesn't really make the situation better that's

[00:54:12]   basically the situation that we ran into with the 802s going from 27,000 to 30,000 to 33,000 we gained a little bit of power for sure we gained a little bit of power but

[00:54:27]    that was really only in the house once I started flying them outside using a higher amount of cruising throttle because it's bigger outside the the the 802s felt

[00:54:41]   terrible because they were just getting too hot and when when Motors get too hot the magnets saturate with that heat and magnets don't work well the hotter they get and so they end

[00:54:54]   up losing power and you've got this round and round you go basically oh man this propeller just like fell onto this motor shaft let's let's tighten it up a little bit if

[00:55:07]   you've got a propeller that's too loose on a motor take your least favorite sharp tipped tweezers it's going to bend the tips which is why you want to use your least favorites take it put it into

[00:55:17]   the propeller hole at a 45 degree angle and rotate it around what you want to do is dig into the plastic you're going to dig in and leave a low spot but then to the left and right of the low spots the

[00:55:34]   plastic is going to go up and create two high spots and then that propeller will grab the prop shaft a lot better like this one just did and now you've fixed your propeller the other way to do it is

[00:55:47]   to put some CA superglue in there and let it dry and the superg glue when it dries it has a lot of texture and so when you put it on that texture is is like grip and will bite against the

[00:55:58]   propeller shaft the problem with doing that is if you take the prop off and put it back on take it off and put it back on it'll push all that superglue out so it's a it's a temporary kind

[00:56:09]   of fix and then you just do it again no I do not want a tattoo that's a weird text message to get Bob Bruce says happy birthday my birthday was on the 4th I also turned 43

[00:56:29]   hope you had an awesome day damn dude a whole bunch of us that are 43 bunch of old heads big J 541 says happy birthday thank you dude stepen Woodruff says have you seen the heads up tiny

[00:56:40]   whoop race build I have indeed any thoughts on the components I know it's really not your area of expertise so there there's really nothing there's really nothing extraordinary about his

[00:56:52]   race build that's pretty much the race build that all the racers have been doing doing for probably about the last year and a half his race build is almost

[00:57:03]   identical to the race build that I did on Joshua's website FPV all.com so it's a it's kind of a known quantity I I love that that Evan has a really popular video showing how to do that

[00:57:15]   build because it's a great build but that build is kind of old hat by now for racing it's awesome it's what pretty much all the racers run so there's nothing wrong with it but I mean

[00:57:26]   you know I I I I watched the entire video expecting to like to get a little bit more out of it and at the end of the video I was like okay I should have just I should have just assumed that it

[00:57:40]   was the same race build that everybody does but that's fine those guys did an awesome job they they made a video where and where there kind of wasn't one although I'm sure there is

[00:57:50]   another video I'm gonna try to remove Tokyo Dom told me that the right way to remove the heat shield heat sink heat spreader on the WalkSnail VTX is with plastic razor blades so that

[00:58:09]   you don't screw up the components on the the VTX and apparently instead of trying to pry it off you cut the adhesive on all four corners a little bit at a time and then eventually

[00:58:25]   it'll just pop off off so that's what I'm going to try here but first I'm going to try to separate the rubber grommets because they've been pushed together for so long that they have become one with each

[00:58:43]   other that's ridiculous get out of there come on there we go get out of there there we go okay so he says do you guys really need to see this do you really need me to do this

[00:59:00]   on on camera says you go into the corners I love the the idea behind these plastic razor blades is great man not not being so worried about cutting the [@$#%] out of yourself I am into

[00:59:19]   that razor blades and xacto knives are horrifying man the these plastic ones like they're not I mean I guess if I really drove this into my hand I might be able to cut myself but I don't think so the

[00:59:35]   the edges are really not all that sharp it looks like one Edge is is a slightly has a sharper angle to it so that's what I'm doing right now I'm just kind of running running it

[00:59:53]   from the corner down the edge I got to be honest I don't think it's working but maybe it is I've done two sides now it just it doesn't seem it's thin enough to really get under that it's just

[01:00:12]   it's bending the corners of the plastic razor blade quite a bit luckily that I got a big old box of them for a birthday so once I ruin this one I can just swap another one this screw is

[01:00:28]   invading my crotchal region get out of there no screwing crotch no CR never mind all right hold on let me get these screws out of the canopy these M12 1.2 x 12 big J says happy birthday thank you

[01:00:48]   dude oh I already did that one metadon says it was the BetaFPV cross AO with e that came set to 96 that's it good call at least it's two I have did yep you're right you're right yep the

[01:01:02]   beta FPV cross AOS come on 96 skip disco says happy birthday thank you brother brand MC Bean says I feel so old went for a hike got attacked by mosquitoes still tried to fly long

[01:01:13]   range got absolutely devoured my mosquitoes and I had to escape by running back uphill to the car I'm beat happy birthday happy birthday to you as well Bron David Chong says happy and

[01:01:23]   blessed birthday hockey round says who is older Brandon B beans or seatt FP what time you born I was born very very early in the morning I'm almost certainly older I want to say 2 a.m.

[01:01:36]   maybe 2 something a.m I was born I was a pain in the ass as I am now I I did not come out for a long time I was although I I was very premature I had to go directly into I

[01:01:54]   don't know a bubble whatever the hell those things are ICU bubbles or I don't I don't know if it's ICU but I'm running this plaster plastic razor blade down the third side of this heat

[01:02:06]   spreader thing still don't think it's working but I'm just going to keep going I've got one corner left that hasn't been bent to hell but here's this is the side that's equal with the mippy

[01:02:26]    and so it's going to be a lot harder for me to get this down onto this side here but there we go I'm trying got it on there and this is this is it's hard to get these things off and I've

[01:02:45]   heard that they're not selling the version of the WalkSnail VR VTX that doesn't have the the heat shield on it anymore if that's true that means that everybody that wants them to be

[01:02:58]   nice and lightweight is going to have to do this which really sucks cuz this is this does not seem to be working what I'm doing here at all and the other way to do it the one that I previously

[01:03:11]   did was very difficult I've done two of them the one of them I [@$#%] up and broke it no this isn't doing anything it's not it's not thin enough to get in there like like the the

[01:03:28]   Gap is incredibly small I'm going to have to get medevil on it like the last one that I did I'm 50/50 though I I've done two of them the one of them I

[01:03:41]   broke the the other one I didn't I don't remember what I ended up doing was I I I think I was using a I think I was using an X-Acto Knife oh boy this is going to

[01:03:53]   be I did not like doing this last time man what I'm trying to do is just dig it under there ever see a guy bleed on his birthday might be about to I'm not pushing hard on the xacto

[01:04:11]   knife I don't want to show you guys this because if I gash myself open and spray blood all over the place YouTu will probably ban me I mean it

[01:04:24]   does the exact ccto knife does kind of like lock in between the Heat spreader and the chip pretty nicely so I'm not super worried about it popping out and I am like I'm not putting much

[01:04:36]   pressure on it I'm more just like wiggling it back and forth it's getting in there it's getting in there just being gentle all right let's take a look oh that's getting the job done

[01:04:51]   hell okay all right right so I'm just going to be patient with it I'm just going to sit here on all four corners with this xacto knife I'm just going to gently gently

[01:05:04]   put it in between the chip and the and the heat shield and just kind of wobble it wiggle it back and forth not putting a lot of pressure on it's slowly just kind of digging in there

[01:05:17]   so I'm like wiggling it back and forth like this and then I'm also twisting it a little bit because the heat shield is here the chip is here so I'm putting it in the corner and

[01:05:26]   I'm just kind of like to get it to get under and then when I when I twist it's ever so slightly lifting up on the thing you can safely do both Corners here it's not really going to be

[01:05:41]   safe to do this side because there's all these components in the way so I'm just going to focus on these two corners here and hopefully I can pry the thing up and off without really pulling up on it

[01:05:54]   if Tokyo's d as watching this I'm sure he's not happy and I'm sure that he's right I'm sure he has some magical way of doing it I just can't figure it out basically what he says is that

[01:06:09]   you need to cut the the heat transfer paste out of there you don't want to try to pry it up and off because when you pry on any surface mount board it's just that it's surface mount so if if

[01:06:23]   you go prying up on it you can pretty easily pull those pull those components up and off the the PCB and you don't want that but I'm I I don't I I don't see how we would

[01:06:41]   get how we would get under and cut all of the thermal paste off of this because these plastic razor blades are just not long enough let me try it with the exact to a knife though let me try to go along the

[01:06:57]   side there did that do anything no that didn't do anything the problem is the the heat shield is just so flat against the it's just so flat against the the chip that I I can't I

[01:07:15]   can't really get anything in there I mean I can barely get this xacto knife into the corners of the damn thing hopefully they have not discontinued the the version of

[01:07:33]   this that has not had the heat spreader heat shield installed because that's the best case is to not have to do this at all but I've only been doing this for a

[01:07:50]   couple of minutes and I've got this got this xacto knife in here pretty good on this corner and I'm not bending the xacto knife all up yet and I got like a nice little Gap going

[01:08:08]   there so the way that I did last the the last one which did work is I got a little bit of a gap on the corner and then I just took a really thin bladed screwdriver I think it was this one this

[01:08:23]   is the weha 260 260 I put this guy under there and just started twisting at the screwdriver and that popped it up and off it did take a bunch of force though which is

[01:08:40]   scary but the last one's been fine we've been running it for a while and it's been totally fine and I I don't see another way of doing this I need more of a gap there so I need to need to get

[01:08:51]   the xacto knife back to work and I'm gonna really resist the urge to start cranking on this because as soon as I start pushing hard on this xacto knife that's going to be when it slips out of

[01:09:02]   here and I gash the [@$#%] out of myself so I'm going to be nice and patient I'm just going to keep wiggling it back and forth here while it's buried in between the two

[01:09:14]   layers and every once in a while it twist it a little bit that's going to give it the the like lifting Force this is sketchy man I don't like this at all

[01:09:31]   oh it's in there now oh that might be it I think that might be all I needed yep there we go screwdriver is getting in there okay all right screwdriver is in there and now I'm just kind of doing the

[01:09:48]   same thing but I'm putting more twists on the screwdriver oh boy I remember this from last time man this is it's like really on there and you can't so I used Heat last time and that was a complete waste

[01:10:03]   of time it's a heat shield and it's thermal paste it's meant to deal with heat so the heat didn't really seem to help last time I mean it can't hurt the problem though is that when I use

[01:10:16]   heat the whole Board gets hot and then I can't hold the board because it burns my fingers hatrick says rapid fire top three in order 75mm 40mm prop whoop frames quick and

[01:10:31]   easy I don't necessarily have an order yet the the Mobula 7 V4 is the one for analog rigs where you're going to use a HappyModel board the meteor 75 air is the ones is

[01:10:53]   the one that I use for the WalkSnail builds because they use the BetaFPV cross AIO I don't think there's a third I guess the meteor 75 Pro would be the third choice but it's big and it's

[01:11:07]   heavy but it lets you run the bigger props so you can make more power with it Rabbid rabbit says how are the t-motor 802 25,000 KV 1.5 mm shafts they don't exist they they it

[01:11:24]   doesn't have a 1.5 mm shaft it's got it's a it's a 1.5 mm shaft down below the Bell which all of these are but it's a 1 mm shaft up above the Bell they they Market them very weird and they

[01:11:39]   make it seem like it has a 1 and a half millim shaft but it's not above the Bell that it's one and a half super annoying Justin Waller says I'm running 22,000 KV 1102 on a 75 Pro analog rig

[01:11:50]   with tri blades and absolutely rips outside get those Tri blades off of it dude the the the the GemFan 45 mm Tri blades are super out of balance switch over to by blades and it'll fly even better

[01:12:08]   somebody pointed that out to me and then I tested it and I was like Blown Away by how out of balance the the tri blades are and 22,000 KV should have that should be enough RPM for the

[01:12:20]   byblade 45s to make good power boy here we go again more prying hopefully no destroying what I'm trying to do is pry downwards and use the leverage to kind of pick up but it's kind of

[01:12:46]   bending the corner of the of the PCB which is a little bit scary now I'm kind of trying to move the screwdriver down the length of the the heat shields here and that seems

[01:13:03]   to be working we're getting there we're getting there there we go oh it's all set friends that ah we did leave some marks though we left some digs there I think I did on the other one

[01:13:22]    cool I can see I can see the orange plastic from from this guy and it didn't it didn't get in between the layers far enough to get to the to get to the thermal paste so the

[01:13:44]   the I don't know you you if if you're going to go this route you need to find these that are like incredibly thin these are like the reg I don't know I just picked a set of 100 or whatever off

[01:13:55]   Amazon and these are definitely too thick you would need to find a thinner version of this but all is well that ends well in theory hopefully I didn't destroy this the next thing

[01:14:06]   you need to do is wipe off all of the the thermal paste which you want to be careful of that is a I've been told by a whole bunch of You Beautiful bastards that it is a heavy metal and

[01:14:20]    you got to be careful with heavy metals you don't want to get them into your stomach so I'm going to use gun cleaning patches that I have left over for my airsoft days and

[01:14:33]   then we'll be good to go it's just they're basically like just lintree sheets and I always forget that I have them but they're nice to have there's no reason for me to use something lintree

[01:14:51]   it's just this is the closest Cent paper towel that I've got wow what the hell got to really scrape it to get it off Jesus usually thermal paste is more is like looser than this this is

[01:15:08]   pretty pretty thick [@$#%] all right we're getting there though all right there's the center now let's go around the outside nothing to see I'm just cleaning my friends what you do Wednesday I watch

[01:15:34]   the guy clean did a bunch of cleaning was thrilling thrilling stuff I'm using my fingernail on the other side of the that's getting it off that's getting off I guess you don't

[01:15:52]   technically need to remove it you could just leave it on there but I especially cuz it's so thick it's not I I I I wanted to remove it cuz I didn't want to get it to get all over everything but

[01:16:01]   it's like a [@$#%] paste so I kind of wish I'd just left it's not really reusable though I wouldn't be able to put the heat shield back on with it or anything so I kind of may

[01:16:12]   as well have just left it although if if I do ever want to put the heat shield back on the one that I just threw in the garbage can I would need to use fresh thermal paste at which point I'd

[01:16:23]   probably remove this stuff anyway anyway but whatever it's gone now nice and clean all right all set heavy metal residue fell on the other one I just picked that up with my

[01:16:44]   finger like a donkey and the rest of it can go on the floor Okay cool so let's get this put back together we'll put this into the 103 frame and then we'll see how they

[01:16:58]   are actually really excited about the 103s maybe they're amazing how the hell okay this goes like this this goes over here hold on let me just wipe my hands off I I see

[01:17:12]   like little little pieces of something on my hands and I just want it off and I'm also going to just wipe the desk off a little bit better here just to be safe okay M dkin with $25

[01:17:29]   Super Chat he says there are wild turkeys outside my window just thought you'd like to knowturkeys are nasty [@$#%] what is their deal like are you trying to make me eat

[01:17:43]   you chill the [@$#%] out you disgusting Raptor looking [@$#%] like you're already ugly you're nasty and you don't bother my stomach so keep it up jackass I'll

[01:17:59]   eat you all day I'll eat Just Turkey I'll be on an only turkey diet and I'll just wipe as many of you out as possible they're so nasty that even South Park has has immortalized their

[01:18:19]   awfulness thank God for turkeys man I don't know why I don't know why I said thank God for turkeys give me a break it's my birthday I guess it's because I I I can eat them without getting a tum

[01:18:33]   tumach you don't hurt my tummy getting these boards together in a way that they're like kind of happy is takes a minute but I got it all right cool we're going to put this under the 103

[01:18:56]   frame which is this one arrow in the back of course because we're not a bunch of idiots all right here we go is this okay not doing it with the bench cam you get to see all the faces

[01:19:16]   that I make when I'm doing this stuff I figure that's probably more interesting than just seeing me put a tiny whoop canopy into a frame for the seven 100th

[01:19:26]   time okay we're good and so we're going to put the front screw in first because it does not go through the canopy and if you don't do that you'll have to take the whole thing apart again

[01:19:40]   to put the front screw in because the lens gets in the way the snuffle upus setup with the Mobula 6 canopy has the the front lens right above the the front screw always put that front screw

[01:19:55]   in first Drive the front screw in and then take the boards and push down on them a little bit and just look how the rubber grommet kind of reacts you want to keep screwing it in until the rubber

[01:20:06]   grommet is kind of like poofing outwards a little bit the the farther you screw that front one in the stronger it's going to be although it doesn't really put up with a lot of the abuse the the

[01:20:17]   side and the rear ones do on this Mobula 6 canopy you actually need to cut the front you need to cut the front mounting hole off of the canopy in order for it to

[01:20:35]   sit in order for it to not hit against the UFL Port and so when you do that the front screw doesn't go down through the canopy but it's fine it's totally strong and these

[01:20:49]   mobula 6 canopies used to be they used to not have a and yours might not even if you have one of the older Mobula 6 canopies it will not have the front mounting Point and that's

[01:21:00]   totally fine I I've not seen any difference in strength there is more than likely a difference in rigidity having that front mounting Point in the frame but it's not so bad that like

[01:21:19]   I've really noticed it but all things considered if you can run it as a four screw you should pick it up last screw going on plug the motors in fire it up in BetaFlight get them spinning the right

[01:21:43]   direction and then we'll fly all right cool three canopy screws are in let's just tighten them up a little bit same kind of deal the way that I do it is I tighten it up a little

[01:21:57]   bit and then I push down on the pcbs that squishes the the rubber grommets together and then I can just kind of see is it pushing up against the canopy or is there a little Gap when I push it

[01:22:11]   down and then I'll just screw it down a little bit until it's just kind of smushing the grommets a little bit in in their in their when I'm not pushing down on the PCB

[01:22:26]   I want the grommets to be a little bit ballooned out that tends to be the spot where they're tight enough but not too tight what I don't want is to push down on the PCB and have the screw pop out of

[01:22:42]   the hole or there to be a gap between the rubber grommet and the canopy that means it needs to be a little bit tighter and you want to run these as tight as possible so that you can get as

[01:22:54]   much as much contact between the threads and the post that's where you get the strength if if you've got that plastic post and you've only got the screw going in a little bit's going to rip the

[01:23:05]   screw right out it's going to strip it out you want to get the screw down as as deep into that plastic post as you can I'm using these m1.2 by12 screws which will go I've not had any issues

[01:23:17]   with them yet in using this kind of Method Man these motor leads are long geez as hell I could plug I could wrap the the motor lead around the duct on the outside and then

[01:23:30]   plug it in they do that because these motors are I'm sure getting used on 3s toothpicks sorry 3-in toothpicks rather definitely not 3s toothpicks since they're 22,000 KV although boy

[01:23:46]   that would be hysterical for about 3 seconds not even there we go there's two of them look at all that extra motor [Laughter] wire if these are good I will put different motor wires on

[01:24:07]   these because this is absurd the a chunk of the of the extra fatness of these motors is in these motor wires I I could I could probably save at least 02 of a gram maybe more

[01:24:23]   by shortening up the motor wires tempted to do it right now but I'm not shortening tiny whoop motor wires on my birthday that's not how this day is going to

[01:24:38]   go all right they are all plugged in good God what like a [@$#%] Spiderman it could just oh it sits up on the motor wires that's the that's the that's the deal it's a it's a turtle

[01:24:59]   mode it's not Turtle mode [@$#%] this is wild hold on I need to I'm GNA put them in between the ducts just to get him out of the way God damn dude okay get in

[01:25:22]   there get in there you I'm pulling them up between the ducts here my God man there we go and there we go and there we go come on get up in there there we go okay that's all

[01:26:00]   set that's crazy looking it should be fine though they'll probably stay up in there all right now we're good all right so Che friends Jason black says cake day I'll

[01:26:31]   fax this with the SE fv.com link thank you dude James Thomas with a $5 Super Chat he says so did you make your decision on 102 10:3 1102 1103 happy birthday you're looking at at it right

[01:26:44]   now James This Is Us trying the 103s next up at some point is going to be 803s I don't know of any well I've got the 1102s over there we'll try those again I don't know of any 113s that

[01:26:55]   are a three bolt if you do let me know I'll totally try them but I mean these 103s are probably going to be too big so an 1103 is just going to be even bigger but the problem with 113s

[01:27:06]   is they're all four bolts for like toothpicks and stuff biochi with a 20 Royale Super Chat he says greetings from Brazil happy birthday thank you dude rock crawler with a $20 Super Chat he says happy be

[01:27:18]   Aon thank you brother you guys are too kind where was I at here we go go rabid rabbit says where where are the motors at for sale they're right here they're in my hand just message me

[01:27:34]   and I'll sell them to you Scotty Scott says happy birthday got my gangly fan looks great on my bench next to my new Omni fixo Scotty Scott's got all the good tools very cool man enjoy it enjoy

[01:27:45]   it Striker says what a 3-in toothpick frame on 4S with 1404 be effective for racing if not what's good for 3-in racing me and my boys are thinking of starting a micro Racing League at a

[01:28:00]   soccer field near us the the problem with the toothpick as a racing build would be durability it's you're with racing you're going to crash often and hard so I I would not go down that route there

[01:28:18]   are probably 3-in racing frames start hitting all the websites and look in the 3-in frame section I'm pretty sure you'll be able to find a 3-in racing frame I'm pretty sure

[01:28:29]   pyro drone has one called I think it's rug's old design like a 3-in floss maybe but I the I would not do it with a toothpick frame you're you're going to break too many arms Striker

[01:28:43]   also asks would you recommend a different size even for racing in smaller environments than than 5 in now 3 in is the way to go and 1404 is a really good size so I would do like

[01:28:55]   1404 t- Motors the 4600 KV they're going to absolutely rail but I I don't know what to recommend on the frame but I'm pretty sure you'll find one cbfv says happy birthday thank you dude

[01:29:05]   Striker also says when I say toothpick I mean a frame meant for 1S on 4S 4600 no don't do that a 1S frame is designed to be strong enough for the weight of 1S if you put a 4S battery on

[01:29:19]   it's going to explode the first time you crash Kila zebra says welcome to 43 SE and brains B beans thank you dude 10c run time says I got some of those 31 mm 1.5 mm gem fans in both TR and

[01:29:33]   quad blades for my RS 0802 30,000 KV will one be massively better than the other the tri blades the the quad blades are unfortunately way too heavy but run them both I've heard

[01:29:46]   from a couple people that they just for whatever reason like the way that the quad blades fly for me the the quad blades are just too heavy and the the response time goes to [@$#%] but

[01:29:58]   some people don't put their rigs into prop wash all the time I do a lot of moves that really like put these things directly into their own dirty air so it's depends on the

[01:30:10]   pilot doing things out of the out of order let me unplug this battery because beta flight's going to take a minute to fire up here MC buas says happy birthday I was a bubble baby to check

[01:30:21]   your PayPal oh [@$#%] I see duel Deuce's name where's it at there it is Mick buas with a $25 Super Chat thank you brother he says happy birthday whiskey and Waffles fun whiskey and

[01:30:35]   Waffles oh oh that makes me cringe just thinking about it thank you brother very very cool of you make that unread so I don't miss it crom says have you seen any adverse

[01:30:51]   effects removing the heat shield on the 1S WalkSnail VTX it overheats a lot quicker but you just blow on it or I mean it overheats pretty quick with the heat shield on there so it's

[01:31:07]   it's not it is significantly worse I I will absolutely say that but unplug it when it's getting too hot or blow on it or get a little fan going and it's not too bad it's annoying

[01:31:23]   the the big biggest problem is when you crash it somewhere that's far away because like even turning down the even turning down the output power doesn't really have much of an

[01:31:38]   effect I've got mine on 25 Ms and they overheat incredibly quick so you got to be a little bit careful with that but other than that it's not too bad Motors are all now

[01:31:50]   spinning in the right direction let's check them props out props out props out props out we're good let me get a I will show it to you guys let's get an RPM measurement on this unloaded and

[01:32:07]   then we'll do it loaded oops 82,000 oh wow that that one motor is way down what the hell's going on motor 2 hold on let's check it again 8

[01:32:25]   3,000 78,000 is the highest I saw that's kind of disappointing 70 77,000 77,000 so motor 1 is just hot motor 1 is is has Mega KV and the rest have normal amounts of

[01:32:45]   KV so I guess the the I don't know little bit of a manufacturing defect there let's put propeller on one of the these motors I'm going to put it on motor 2 nope I'm going to put it

[01:32:56]   on motor number four and we're okay no I'm not we are going to pull the battery cuz the WalkSnail is probably overheating at the moment I went to put a propeller on and it just fell onto

[01:33:07]   the motor shaft so let me try to find a fresh set of 1610 and hopefully they will grab these motor shafts a little bit seems like maybe the the motor shafts on

[01:33:27]   these 103s are ever so slightly undersized which is kind of annoying but I would actually rather them be undersized a little bit undersized if if they're too

[01:33:43]   undersized that's going to be super annoying let's see this is a brand new set of propellers and it's perfect okay so they're actually perfectly sized for fresh propellers that you haven't run

[01:33:54]   down a pin Vie which is a breath of fresh ass these motor shafts are the perfect diameter outer diameter cool they fit really good on there okay so let's fire this thing up with the

[01:34:21]   propellers on I've been doing this with pretty much all motors do you guys remember what the we did this the other night with the 102s do you guys happen to remember what RPM we were

[01:34:31]   getting with these are also 22,000 KV but since it's a bigger motor it should crank these harder especially in a loaded situation where there's no incoming the incoming air is not moving

[01:34:44]    so let's go here and let's go here here we go I'm not going to do motor one cuz it's crazy all right 52,000 I saw 52,000 I think that's what we were getting with the 102s that is not good

[01:35:03]   news pretty I'm pretty sure that's what we got the other day so potentially what that means is that 102s are a big enough Stater for the KV and so what we should see

[01:35:32]   here is no extra power from these 103s and the little bit of extra weight in the in the loaded scenario that we just tested with no incoming the incoming air is not moving that is

[01:35:48]   the scenario that's harder on the motor so that is where a bigger motor should do better so not looking great for the 1003s but we're going to try him anyway

[01:36:03]   obviously rock crawler thanks again for the $20 Super generous Super Chat Robert G says soak a bit of IPA to soften the compound oh I forgot about that I wanted to do that this time I totally forgot

[01:36:18]   by the way happy birthday thank you Robert he also says acetone will work if you have it biochi thank you you again for the 20 Royals super generous as well parkour guy says better late

[01:36:28]   than never happy bday my dude thank you man James Thomas thank you again for the 55ll Super Chat very generous Striker says first crash of 2024 was on January 1st crash every day man every day is a

[01:36:41]   crash day parkour guy says for an analog 75 Jungle Gym Basher with plenty of power Mobula 7 V4 frame what size motor would rip the hardest and what minimum KV would you go trying to build a a

[01:36:54]   1s standard like we've talked about 802 27,000 KV is the way to go 30,000 KV is even better but you're going to have to buy a set of 30,000 KV 1 mm shaft Motors take them

[01:37:10]   apart then you're going to have to buy a 1 and a half MIM motor shaft Bell and take those apart and mix and match if you do that use the RS use the HappyModel RS8 2 Motors they're cheap

[01:37:25]   they're readily available and I think it's the lightest Bell so you can make yourself a Frankenstein 30,000 KV or even 33,000 KV with the iao ioma imop when they come back in

[01:37:41]   stock shriker says hot take if you don't crash every pack you aren't pushing hard enough I'm with you I agree Ellen says happy birthday brother thank you dude where's my wrench says BetaFPV

[01:37:53]   is .79 per thank you dude copad says scroll further that Super Chat was like 20 minutes ago it happens famg says it's your birthday happy birthday thank you brother my dad's in the chat what's

[01:38:08]   up Dad nasty FPV says happy birthday 25 looks good on you oh I wish I might look 25 but I certainly don't feel it nor am I I'm 43 today ramdo says how would you spell

[01:38:20]   snuffleupagus I couldn't I couldn't find it on Wiki after two minutes of research really that's I guess it's hard to spell it in a way that's searchable try Siri ask Siri how to

[01:38:31]   smell stuff snuffle upus see if she knows fam G says if you make flames on your ESC you can make a wish and blow it out you never know these are Big Motors t- bird FPV is in the house he says

[01:38:44]   happy birthday beautiful thank you brother Denzel the terrible says did you get birthday kisses from Maggie I did indeed James Thomas with a $20 Super Chat thank you brother very generous

[01:38:54]   first whoop build Mobula 7 probably WalkSnail or hd0 what non SPI flight controller and motor combo with the WalkSnail or HD zero boards also what's the deal with

[01:39:10]   enamel wire antennas is that actually good for more than 50 feet sorry whoop Noob and again happy birthday the enamel antennas are totally fine Mobula 7 with WalkSnail or hd0 is

[01:39:25]   exactly what I've been working on here for the last couple of months I do not have an answer for you on the motors because I have not found my perfect motor yet the best that I've found so

[01:39:35]   far are the 102 22 I'm sorry no no no the 1102 BetaFPV 22,000 KB Motors but they still don't make quite enough power for me we're about to test RC and power 1003 22000 but the little motor

[01:39:53]   tab test that I just did was not super encouraging so I don't think these are the motors but we shall test them anyway definitely don't go 802s they are not big enough you want 102s or

[01:40:11]   803s the problem with the current 803s that are in stock is that none of them are high enough kyv the problem that we have with these 102s also and the 1102s is they're they're not quite High

[01:40:23]   Enough KV if we had an 1102 or a 102 that was 25,000 KV that would be much better but we do not so I will continue to test more and more and more and more [@$#%] until I find a motor

[01:40:36]   that's acceptable VCI is making an 0803 27,000 KV motor but it's out of stock until the middle of next month I have an order in for them I have a feeling that that's going to be the one

[01:40:50]   unfortunately it's only a 1 mil motor shaft so I asked them about making a one and a half millimeter motor shaft version and they said sure we can do that minimum order quantity is a

[01:41:00]   thousand and I said i' I'd have trouble selling a hundred of them let alone a thousand I think it's a th individual Motors not a thousand sets of four but still I there's no way

[01:41:13]   in hell that I'd be able to move that many Motors but I don't know I I hopefully me asking for it has them thinking about it and they'll maybe make it in the future because nobody's

[01:41:27]   going to buy a 1 mm shaft 803 that doesn't make any sense that that motor is way too heavy for the one mil shaft they might be able to find a manufacturer that that's doing like a

[01:41:39]   bind and fly that'll use those Motors that wouldn't surprise me but that's going to be a BNF that breaks all the time so I don't know we shall see here we go friends

[01:41:54]   103s James Thomas thanks again for the Super Chat man super generous Adam C says happy birthday Striker says tiny trainer spec league would be really cool that's exactly what you want to do that

[01:42:04]   is how you do a three-inch Race League is with tiny trainers yep I forgot about the tiny trainer they've already got tiny trainer race leagues too so you can just piggyback off their rules and

[01:42:15]   the the combos that they're all using here we go nope absolutely not nope worse than the 10 two is cuz they're heavier ah man that's a shame these need to be like 30,000 KB

[01:42:33]   look how [@$#%] fat they are what is interesting though is that the pit Loop performance is great because but it's fine on the 102s too it's a big chunky motor and it

[01:42:45]   just it doesn't have enough RPM it's not even worth it to fly the rest of this battery it makes the exact same amount of power which which is exactly what we saw in that

[01:42:58]   quick motor test but it's a little bit heavier now so it's we've just added a bunch of weight with no benefit because the KV is not high enough so what we're going to try is

[01:43:12]   going up to Tri bladed propellers which I already know how that's going to go because I've done this a million times but I've never done this with a motor that's this beefy the the main

[01:43:24]   problem with the tri bladed propellers is that none of them are all that well balanced so you're going to hear it sounded nice and smooth just now and the pit Loop was was totally happy you're

[01:43:38]   about to hear it gets significantly louder and you'll probably see more power but we might need to back the pit Loop off because of the extra vibrations that are going to happen here

[01:43:52]   these are G fan 1635 damn I'm good GemFan 1635 Tri blades ton of pitch the the the GemFan by blades are 1610 1.6 in in diameter 10 pitch this is 35 pitch three and a half times as much pitch so this

[01:44:18]   will obviously make a bunch more well maybe more often than not these propellers are too heavy for the motors this is a big ass motor though so I think that this will have

[01:44:30]   enough grunt to crank these propellers really nice and deal with their weight we'll get to see that by how the PED Loop performs but the problem is more than likely going to be

[01:44:44]    the imbalance of these propellers but let's see you'll probably hear like a screeching noise or like a rattling noise with these propellers let's give it a

[01:44:56]   shot battery is still in there I just missed something ramdo says same few spins fre lojo stream laggy not my end dropping YouTube is is a nightmare lately hockey rounds hockey round says new

[01:45:13]   motor fund and transfer $20 over towards the oh dude thank you hockey rounds I completely forgot about that so this goes go to 20 and then we're going to go RC in

[01:45:32]   Power 102 we'll take out the KV and I'm going to double it because I bought two sets of the the RC and Powers 10 102 and 1102 no no they're not 1102 they're 10:03 thank you dude for that reminder I

[01:45:54]   I I knew I was going to forget and I did it looks it's not I'll fix it can't have it not look right there we go that's better okay trib lated 1635 big crazy

[01:46:14]   propeller so first I want you to listen and then we'll rail it around the room let's see Ark says the best part about how bad the 103s are is the flight time it's so bad oh boy here we

[01:46:34]   go oh wow it doesn't even make any extra power they don't seem super unbalanced no I can hear it though I can hear it a little bit's a little like oh this is awful oh

[01:46:53]   boy this is worse Jesus I mean if I just sat it Full Throttle see so you also see that we're starting to get bounce back in the tune ready see that little little bounce at

[01:47:12]   the end of the flip and roll wow that just annihilated this battery these props are not the answer these props are significantly worse than the

[01:47:23]   than the by blades yikes and it really [@$#%] stomped that battery okay so let's get these props off the last Tri blades that we're going to try are the 16008 GemFan tri blades so 1.6 in 08

[01:47:42]   pitch but it's a triblade so there is a chance that it'll make more power than the 1610 by blades but it won't but we'll try it anyway because I don't know because just

[01:47:59]   because these 1608 are a lot lighter than the 1635 let's see how they are there and there and there and there all right that battery is shot and it's hot we're going to use a

[01:48:33]   battery right off the charger to give this as fighting of a chance as possible and these long ass motor wires are starting to pop out put them back in

[01:48:47]   here get back in there you now whatever they're all starting to pop out and it's not going to fly good with these anyway here we go I'll try these motors on like a

[01:49:02]   toothpick or something they'll probably be good with like a 2 and a half inch prop or a 3inch prop or something GemFan 1608 Tri

[01:49:14]   blades here we go W there all right way better than in the 1635 not as good as the as the by blades though okay oh God it just feels awful it's way it was better on the

[01:49:48]   102s damn beta FP 1102s are still the best option this isn't terrible this is pretty shitty it's not the worst was just it just s It On full throttle and you see the little bit of

[01:50:20]   wobbliness oh God I couldn't get it off the ground this is this is no good the BetaFPV 1102 2200s on the GemFan by blades continue to be the best see all that wobbliness that's cuz these

[01:50:36]   that's twofold it's cuz these props are heavier but it's also because it's not making enough power and yet we're at a minute and 20 and the battery is down to 3.5 already I have been hammering the

[01:50:47]   [@$#%] out of it though oh I missed it this feels awful it feels heavy so these motors will be a much better combo with the the bigger props as we talked about earlier

[01:51:14]   that's a shame but I'm I I can't say that I'm super surprised to be really honest 10:03 is a big jump in motor size versus 102 think of it this way 2 millimeters tall to 3 mm tall that's

[01:51:32]   50% more height and the the height of the Stater is what does all the work the width of the stator is just more mechanical torque the height of the stator actually pulls the the the the

[01:51:46]   vertical part of the winding is what pulls the magnet over across so kind of I I had I I I had High Hopes but they were I I had a feeling this is the way this was going

[01:52:04]   to be this is the way this is going to go but but this was a really good test to do because what we learned is that even a 10:03 look these 1635 props are no good that that's one of the main things that

[01:52:23]   we learned here and we also learned that even the triblade 16008 need more KV the the the problem that we keep smashing into is a KV issue none of these motors are a high enough KV to

[01:52:38]   give us the RPM that we need for the good set of propellers which are the 1610s these these 1610 propellers [@$#%] stomp every single other prop that's available and we just we don't have

[01:52:54]   enough KV for them I lost one of the there it is one of the 1610 so bigger Motors like the the BetaFPV 1102s they're a little bit of an aberration in that they're only 22,000

[01:53:11]   KV but they're they're making a little bit more power than the 102s I'll bet you if we spin them up they actually turn a higher RPM and we'll do that on Friday probably we'll dive back into

[01:53:25]   the BetaFPV 1102s because I'm out of Motors to test now so we'll go back to the BetaFPV 1102s and what I'll probably do is compare them to the RC and power 102s again

[01:53:41]   and we'll spin both of them up unloaded and loaded and we'll what I think that we'll see is that the the BetaFPV 1102s are going to ramp up to a higher KV even even though they're

[01:53:52]   marked as 22,000 KV I bet you they turn the equivalent of 22,500 23,000 something or maybe the RC and power 102s turn lower than 22,000 KV but I I I

[01:54:08]    a lot of this is leading me to believe that 1610 propellers are Max they they don't need a motor bigger than 10:02 for 22,000 KV maybe and we'll know this when we spin both Motors up maybe

[01:54:32]   they are benefiting from the 1102 Stater maybe 102 is ever so slightly too small and then 1102 is just the right motor size for this propeller on at 22,000 KV what I'm really excited about the VCI

[01:54:50]   Motors is that they're 26 7,000 KV and so at 27,000 KV 102 might not be big enough luckily 803 is more Stater volume than 102 probably than 1102 as well so 0803 even if it's not more Stater volume that

[01:55:15]   3 mm height is going to make a bunch more power than any of these 2 mm height Motors so bigger more powerful Stater size higher KV right that's what we want so

[01:55:31]   I would still love though to see someone come out with a set of 102s in 25,000 KV CU I bet you I bet you they have just enough Stater size to crank that higher KV

[01:55:48]   but I I weirdly don't think that see that unfortunately so that's that my friends I'm going to shut this down a little bit early I meant to do 6 to8 but I ended up doing like no no this is perfect 6

[01:56:05]   8:40 I think I came up at about 640 let me get caught up on chat though real quick do you guys want me to fly these 103s anymore I I really don't they they don't they're they're not doing anything for

[01:56:21]   me but it would not the run time is going to be worse because they're heavier they're they fly worse than the 102s I mean I guess if you really want me to I can back to back

[01:56:32]   them let's do that just just for the sake of being totally thorough I'm not going to tell you which one is which I'm going to fly one of them and then I'm going to fly the other one one of them is

[01:56:45]   going to be on 103s the other one's going to be on 102s and you have to try to figure out which is which they're both on the same everything and they they even both are the same

[01:57:04]   exact all up weight now that I remove the the the heat shield from it so I still have two batteries fresh on the charger I'm going to put one in one one and the other James Thomas with a super

[01:57:18]   chat thank you brother I will read your comment in a minute let me just finish up this testing here we will finish strong speaking of Weights let's weigh

[01:57:32]   them damn dude disappointing disappointing but expected so maybe a little bit less disappointing I guess I don't know 102 rig is 43.6 gram 103 rig I can feel that it's

[01:57:54]   heavier what 47.2 how is it that much heavier it feels like it good god oh no that makes sense they're they're almost a gram heavier each Jesus it physically feels heavier when

[01:58:12]   you pick it up I'm not going to fly the whole battery so you can't cheat and just look at the abysmal run time on on one versus the other and they're they're both in the

[01:58:28]   same color frame so you can't cheat there either all right here we go see if you can pick which is which hold on there's a huge clump of hair in this

[01:58:49]   one Jesus okay just making sure I'm not showing it on the bottom of the camera it's a cup gameit's a cup game all right we're going to fly this one let me make sure that the uptilt

[01:59:09]   is roughly the same I'm glad that I checked it is not okay there we go now it should be yep okay let's do this one first all right you guys should have no idea I did not show it on the bottom of

[01:59:44]   the thing here we go let me try to shrink this let me shrink this down a little bit maybe that'll help YouTube I don't know probably not but can you not blink okay

[02:00:12]   here's the one all right so here's this guy who oh God all right I'll land it down here so that you can't see what's on the desk and we're going to unplug it and then we're going to take this

[02:00:42]   other one and we're going to plug it in going to fly this one so you're just going to type first or second and you're going to do you're going to do which one was 103s

[02:01:03]   was it first or was it second and you can't possibly know right now because I've only flown the one so hold on a second so were the 103s first or second is the question I I double plugged it in and

[02:01:33]   it's did not let me unplug it and plug it back in here hopefully it'll bind Timmons with a $5 Super Chat thank you homie he says need some more WalkSnail mounts let's release the

[02:01:48]   black batwing files let's do that tomorrow I think tomorrow will be batwing day oh can you arm please not arm can you connect please don't overheat VTX don't overheat come on be cool

[02:02:22]   um well I don't know what's going on here power cyc it one more time antenna looks fine okay well that's not going well why can't anything ever just [@$#%] work I hate everything

[02:03:31]   the the the BetaFPV aios do this an awful lot they just they just need to be rebound it's very strange I would say like every 10 batteries it does that it's super

[02:03:46]   annoying all right this is the other one I take it back they are a little bit different o this is the 102 rig as you probably already guessed because the camera looks

[02:04:18]   different and it wouldn't bind but this does have a little bit less power the 103s the 103s are doing something but they're not doing enough they still don't feel

[02:04:33]   good this doesn't feel good either and I would rather get better run time the 103s are not they're not making enough of a difference to Warrant significantly less run time this

[02:04:49]   is [@$#%] impossible to fly in the house Jesus Christ Christ [@$#%] 75mm trash it's not trash it's just not a house rig ah the the can you guys see it can you guys see that the 103s are making a

[02:05:14]   little bit more Jam not enough though not enough extra Jam to Warrant four extra grams man I can't do anything with these things in the house God damn 75 for the

[02:05:33]   loss oh no we're in the drum set well we tried we tried the 1102s are the the 1102s feel as good as the 1003s but the the runtime is like acceptable on them so they're

[02:05:54]   they're they're the jam for sure interesting interesting so the unhappiness with 75 MIM WalkSnail continues but we'll get there man we'll get there we'll we'll I mean I

[02:06:16]   think we're kind of there there there are no other motors for us to test that make any sense so for the moment it's the 1102s I'm definitely not happy with them you

[02:06:30]   could put them in the meteor 75 Pro frame and they're a little bit better but it's way heavier way way way heavier e do says did you see the word FPV video that RCN power has 0 72s

[02:06:44]   in testing I did not see that but that's awesome I love that CMYK says thoughts on the RC and power GTS v256 4300 KV 1506 is an awesome motor size that's probably a great motor

[02:06:57]   that'd be great for a 3 3 and a half inch three-inch pitchy prop rig three and a half inch rig want to get Fly says happy birthday brother thank you dude ant bvtc says how do you think the

[02:07:09]   GemFan 2023 is would do compared to the others you tested I've the 2023 is are the by blades right GemFan 2023 oh no those are the tri blades I've tested those

[02:07:25]   they're okay they're they're kind of heavy for they're a really durable prop they're really loud the the the there's something about that propeller that it just

[02:07:38]   screams but if you're building like a durable if you're doing like a freestyle 2in rig and you want it to have a durable prop those 2023 is are great I wish they had more pitch they're

[02:07:51]   ALS are pretty low pitch so you got to spin the [@$#%] out of them to get any power from them that's one of the reasons that they scream but really good propeller really durable

[02:08:02]   the with how durable they are I wish I wish they were more pitchy they're they're in this weird area where they're very low pitch but then they're kind of heavy usually a low pitch prop is very

[02:08:13]   lightweight so that's a little bit weird but you can Band-Aid that by just spinning the [@$#%] out of them just put as much RPM into them as you possibly can CBF PB says what's a good weight for

[02:08:24]   a 3-in cine whoop without a battery mine is 250 and I'm wondering if it's too heavy that there's there's really not an answer to that question it's depends on so many things

[02:08:39]    3 inch here here's the best I can do is is give you the weight from this is my lightweight cop and I'll I'll give you a dry weight on this guy it's certainly going to be more

[02:08:56]   than 250 though but it's depends like full-size GoPro naked GoPro GoPro Hero 8 versus 9 10 11 12 I'm at 282 283 and this is my analog Ultra lightweight cine whoop that's set up

[02:09:17]   to carry the hero 8 cuz it's a little bit lighter but so 250 is is that's pretty light that is pretty light for sure Co Powers says something YouTube didn't want me to see it

[02:09:37]   though Co power says there's no possible way for us to see the wobble way too much stutter we'll have to take your word for it that's super annoying I wish YouTube would get their [@$#%]

[02:09:45]   together Arc UK says might need to drop the bit rate on the next stream the stream is the same quality as the 3es there's I there's nothing I can do like I I I can't do that I I just I output

[02:09:57]   either 720 or 1080 it's I believe I'm outputting 1080 and then YouTube does the rest there's there's nothing that I can do about that CMYK dropping the C fv.com link thank you dude Walter says

[02:10:11]   take paramol GJ I don't know what that is what's paral paramol non nonopioid analgesic what is that Tylenol that's Tylenol I'm good I'm okay I don't need no T I don't need no stinking Ty Tylenol

[02:10:39]   James Thomas with the $2 Super Chat thank you homie he says so what flight controller for the WalkSnail or HD zero builds BetaFPV 5 amp cross style

[02:10:51]   flight controller it's really like the only flight controller being made right now that's even remotely usable somebody said C is for cookie 10-sec runtime says will the 102s be as

[02:11:08]   powerful on as 103s on 2s2 rig 45mm baby turtle frame bblades X12 BT 3.0 300 MH it depends it depends on what propellers you are running on it if it's a 45 millimeter baby I don't know what

[02:11:31]   what props are on that but the the 103s the the 103s don't make any sense on this 1610 propeller this propeller is not loading the motor up enough for it to really take advantage

[02:11:49]   of the extra motor size it is a little bit ever so slightly but not nearly enough you might as well run the BetaFPV 1102s if you're going to be running this propeller if you're going

[02:11:58]   to run a more pitchy or bigger propeller than this then the 103s will come alive Justin Walker says have you tried the hype train 24000s I have not I ordered a set when they came they did not have

[02:12:11]   motor plugs I said no I'm not doing that 24,000 KV is not I don't know the the flywoo 10 twos are 23,500 KV when I tested them gu against the other two 22,000 I didn't

[02:12:27]   feel any different any difference so either they're not actually 23,500 KV or this propeller on a 102 22,000 KV is is the realistic Max I don't think that's the truth I think that those fly Woos

[02:12:46]   are are a little bit UND speec but I'm not going to direct solder Motors it's just stupid these these aios that I'm running I have the plug versions of these

[02:13:00]   aios do they even have Provisions for direct soldering Motors I guess they do maybe it looks like you might need to break the plug headers off to direct solder Motors to them and I ain't doing

[02:13:19]   that no it looks like like I could regardless I'm not doing it sorry it's just stupid it's stupid to sell tiny whoop Motors that don't have plugs on them and I'm I I'm just

[02:13:32]   not doing it's just dumb and I I I I tried asking a couple people about them and nobody seems to overrun them including Bubby whose Motors like they kind of are and so

[02:13:47]    if he's not even bothering to use them then why would I I don't know maybe they're a little bit better but I I I I don't think that they would be better like the the all of these 102

[02:14:05]   2200s are here the BetaFPV 1102 2200s are here those hype train motors seemed kind of heavy they would probably be right here they're not going to be a huge jump more than likely and

[02:14:20]   I'm just not I'm just not doing it I'm not doing the the direct soldering thing on Tiny whoops it's just not I'm not going out it's stupid thanks friends my name is Aaron seot

[02:14:32]   everybody calls me Ciotti support me over on Ciotti fv.com join the patreon you get loads of benefits I swear to God you will save more money being a patron than not being a patron because of all the

[02:14:45]   cool stuff that you get and you'll support me and I'll tell you what not to buy and as soon as you don't buy something you've paid your patreon for like a year it's only three bucks a

[02:14:53]   monththat's like 36 bucks a year you you you better damn well believe that you haven't bought something that's $36 at least because I told you that it sucked you're

[02:15:09]   welcome I'll see you guys on Friday be good click all the buttons do the affiliate links use affiliate links when you order [@$#%] on the internet please it's free money for those of us that

[02:15:18]   create content I love you bye I'm not ready here's another couple of insta 360 go to videos from the my cycling gig in Aniston from Saturday I'll put them right next to each other it'll be

[02:15:37]   amazing you'll be amazed all right guys I'll see you Friday be good bye bye bye bye bye bye a n n n